Ball valve with full bore in stainless steel/CPTFE with weld ends or threaded and mounting flange for actuators. Suitable for actuators. Three-piece construction for easy service and maintenance.
| Dimension range | DN 8 to 100 |
|---|---|
| PN | 125 to 64 |
| Temperature range | -30ºC to + 260ºC |
| Material | Stainless steel |
| Article number | Amount |
|---|---|
| AT 3505-10 |
Electric actuator for on/off or control of ball valves, butterfly or where a 90° rotation is required.
Select
Pneumatic actuator for on-off and control of ball valves, butterfly valves or where 90° rotation is…
Select
Pneumatic single acting actuator for on-off and control of ball valves, butterfly valves or where 90°…
Select
Pneumatic double acting actuators for on-off and control of ball valves and butterfly or where 90°…
Select
Pneumatic single acting actuator for on-off and control of ball valves and butterfly valves or where…
Select| Dimension range | PN | Temperature range | Material |
|---|---|---|---|
DN 8-100 | 125-64 | -30ºC to + 260 ºC | Stainless steel |
Shut-off valve mainly for:
- Caustic solutions, acid and saline solutions
- Solvents and alcohols
- LPG, natural gas and petroleum products.
- Warm and cold water, compressed air.
- Saturated steam
PSB.1 Ball Valves
Ball valve Stainless Steel AT 3505 ..., with full bore, weld ends and stainless steel lever. Packing of carbon filled PTFE.
Ball valve Stainless Steel AT 3525 ..., with full bore, threads and stainless steel lever. Packing of carbon filled PTFE.
Tested according to SS-ISO 5208. Leakage class A applies to this valve type.
The valves are approved by TA-luft.
Certificate SS-EN 10204, type 2.2 and 3.1, has to be specified when ordering.
CE-marking
The valves meet the requirements of PED, AFS 2016:1 acc. to category III group 1 and 2. Dimensions to DN 25 satisfies § 8 of the PED, AFS 2016:1.
Surface
Standard surface finish below 3.1 µm for body & ball. Finer surface finish on request.
| Components | AT3505/3525 | ||||||||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| 1 | Body | Stainless steel | |||||||||||||
| 2 | Ball | Stainless steel 1.4401 | |||||||||||||
| 3 | Stem | Stainless steel 1.4401 | |||||||||||||
| 4 | Body gasket | PTFE | |||||||||||||
| 5 | Seat ring* | PTFE, carbon filled | |||||||||||||
| 6 | Stem gasket | PTFE, glass-reinforced | |||||||||||||
| 7 | Box gasket | PTFE, carbon-filled | |||||||||||||
| 8 | Centering ring | PTFE, glass-reinforced | |||||||||||||
| Stainless steel | |||||||||||||||
| 9 | End piece | Stainless steel 1.4409 | |||||||||||||
| 10 | Lever | Stainless steel | |||||||||||||
| *Seats in other material on request, such as glass-reinforced PTFE or PEEK. | |||||||||||||||
| Pressure and temperature, valves with full bore 3505, 3525 | |||||||||
| Seat material | 8-25 | 32-40 | 50-100 | ||||||
|---|---|---|---|---|---|---|---|---|---|
| Standard, carbon filled PTFE 25% | Max. working pressure bar(e)* | 125 (T ≤ 50°C) | 100 (T ≤ 80°C) | 70 (T ≤ 80°C) | |||||
| Max. temperature °C** | 205 (P ≤ 10 bar) | 205 (P ≤ 10 bar) | 200 (P ≤ 10 bar) | ||||||
| PEEK | Max. working pressure bar(e)* | 125 (T ≤ 100°C) | 100 (T ≤ 100°C) | 70 (T ≤ 100°C) | |||||
| Max. temperature °C** | 250 (P ≤ 10 bar) | 245 (P ≤ 10 bar) | 235 (P ≤ 10 bar) | ||||||
| PTFE, glass-reinforced | Max. working pressure bar(e)* | ||||||||
| Max. temperature °C** | |||||||||
Pressure and temperature acc. to applied standards. Note that the pressure- and temperatures above is not related. | |||||||||
| Torque | ||||||||||||||||||||||||||
| DN | 8 | 10 | 15 | 20 | 25 | 32 | 40 | 50 | 65 | 80 | 100 | |||||||||||||||
| Nm | 9 | 9 | 11 | 12 | 19 | 28 | 37 | 52 | 68 | 100 | 112 | |||||||||||||||
Torque above applies for: Carbon filled PTFE, PEEK and glass-reinforced PTFE. | ||||||||||||||||||||||||||
| Kv-value | |||||||||||
| DN | 8 | 10 | 15 | 20 | 25 | 32 | 40 | 50 | 65 | 80 | 100 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| KVS | 6,9 | 6,9 | 12,7 | 29,2 | 48,2 | 73,1 | 107,5 | 215,0 | 275,2 | 498,8 | 877,2 |
| AT 3505 Meassurements weld ends | |||||||||||
| DN | 8 | 10 | 15 | 20 | 25 | 32 | 40 | 50 | 65 | 80 | 100 |
|---|---|---|---|---|---|---|---|---|---|---|---|
| Dy | 13,5 | 17,2 | 21,3 | 26,9 | 33,7 | 42,4 | 48,3 | 60,3 | 76,1 | 88,9 | 114,3 |
| Di | 10,3 | 14,0 | 18,1 | 23,7 | 29,7 | 38,4 | 44,3 | 55,1 | 70,9 | 83,7 | 109,1 |
| Material thickness | 1,6 | 1,6 | 1,6 | 1,6 | 2,0 | 2,0 | 2,0 | 2,6 | 2,6 | 2,6 | 2,6 |
| AT 3525 Measurements BSP threads | ||||||||||||||||
| DN | 8 | 10 | 15 | 20 | 25 | 32 | 40 | 50 | ||||||||
|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|---|
| G | 1/4 | 3/8 | 1/2 | 3/4 | 1 | 1 1/4 | 1 1/2 | 2 | ||||||||
| E | 13,1 | 16,67 | 20,95 | 26,44 | 33,25 | 41,91 | 47,8 | 59,61 | ||||||||
| K | 13,5 | 13,5 | 16,5 | 17,5 | 20,5 | 20,5 | 24,5 | 25,5 | ||||||||
| W | 21 | 21 | 27 | 33 | 41 | 51 | 56 | 68 | ||||||||
| No. of threads | 19 | 19 | 14 | 14 | 11 | 11 | 11 | 11 | ||||||||
Measurements in mm. | ||||||||||||||||
Can be provided with different types of actuators and limit switches. (See separate datasheet AT 3830, AT 3831, AT3840, AT3841, AT 3940, AT 3941, AT 3910, AT 3911). Can also be supplied with stem extensions and dead-mens handle (open or close).
Other ends available:
Weld ends:
| DN | AT 3505, weld ends | AT 3525, threads |
|---|---|---|
| Article No. | Article No. | |
Options:
Seals:
FS = Fire-safe
GF = 25% glass-filled PTFE
PEEK = Seats in PEEK-material
See separate Pressure/temperature diagrams for differents seats.
Connections:
DIN = Weld ends acc. DIN/SCH40
SMS = Weld ends acc. SMS3008
NPT = NPT-threads
Exemple:
AT 3500-25FS (Fire-safe execution)
AT 3500-25GF (Seats of glass-filled PTFE)
AT 3520-25PEEK (Seats of PEEK)
AT 3500-25DIN (Weld ends acc. DIN3239, 1 and 2)
AT 3500-25SMS (Weld ends acc. SMS3008 )
AT 3520-25NPT (NPT-threads)
